Hercules version 3: TCP/IP networking with Hercules

This page describes how to set up TCP/IP connectivity between a Hercules machine and the outside world.

Since Hercules runs as a user process under the control of a driving system (usually Linux/x86 or Windows), it does not have direct access to the driving system's network adapter. This presents a problem in establishing connectivity between the network and the TCP/IP stack of an operating system running under Hercules.

But thanks to a technique originally demonstrated by Willem Konynenberg, it is possible to establish a virtual point-to-point link between the TCP/IP stack running under Hercules and the TCP/IP stack of the driving system. The driving system is then used as a router to pass IP frames between the Hercules TCP/IP stack and the rest of the network, as shown in the following diagram:

        |     Linux/x86 Driving System   |
        |                                |
        +-------------+                  |
        |  Hercules   |                  +--------+
        |-------------|                  |  eth0  |
        |   OS/390    |      TCP/IP ------------------> Network
        |   TCP/IP    |                  ||
        |-------------|         |        +--------+
        |    CTCA     |         |        |
        ||         |        |
        +------|------+  |
        |  /dev/tun           tun0       |
        |      |                |        |
        |      +----------------+        |
        |       Virtual CTC link         |
        |                                |

The virtual CTC link is provided by the Universal TUN/TAP driver developed by Maxim Krasnyansky. This driver creates a tunnel which appears to Hercules as a character device (/dev/tun0 or /dev/net/tun) and appears to the driving system as a virtual network interface (tun0). The Hercules 3088 driver makes the tun device appear as a CTCA (Channel to Channel Adapter) to the S/390 operating system running under Hercules. Each end of the link has its own IP address which is distinct from the IP address of the driving system's real network adapter.

The Universal TUN/TAP driver is currently only available for Linux, Solaris, and FreeBSD.   However, similar functionality may be obtained on Windows 98/Me/2000/XP systems (but not Windows NT) via the CTCI-W32 protocol.

Installing the TUN/TAP Driver (Linux 2.2)

The Linux 2.2 kernel does not include the TUN/TAP driver, so you need to install it using the following procedure:

  1. Download the file tun-1.0-1.i386.rpm from http://vtun.sourceforge.net/tun
  2. Install the driver using the following commands:
    (enter the root password when prompted)
    rpm -ivh tun-1.0-1.i386.rpm
    chgrp xxxxx /dev/tun*
    (where xxxxx is the group under which you run Hercules)
    chmod g+w /dev/tun*
    chmod o-r /dev/tun*
  3. Edit the file /etc/modules.conf (it is called /etc/conf.modules in some distributions) and add the following line:
    alias char-major-90 tun
    This causes the TUN/TAP driver to be loaded automatically when a /dev/tun* device is opened by Hercules.

Installing the TUN/TAP Driver (Linux 2.4)

The TUN/TAP driver is delivered as part of the Linux 2.4 kernel, and if you are using one of the popular Linux distributions you will find that the TUN/TAP driver is already installed. If not, then you must rebuild the kernel with the configuration option CONFIG_TUN=m specified.

Note that the version of TUN/TAP in Linux 2.4 differs from the earlier version in that it allows access to all TUN interfaces (tun0, tun1, etc) through a single character device /dev/net/tun, instead of defining multiple devices /dev/tun0, /dev/tun1, etc.

The procedure for completing the TUN/TAP setup for Linux 2.4 is shown below.

  1. Use these commands to create the TUN device:
    (enter the root password when prompted)
    mkdir /dev/net
    mknod /dev/net/tun c 10 200
    chgrp xxxxx /dev/net/tun
    (where xxxxx is the group under which you run Hercules)
    chmod g+rw /dev/net/tun
    chmod o-rw /dev/net/tun
  2. Edit the file /etc/modules.conf (it is called /etc/conf.modules in some distributions) and add the following line:
    alias char-major-10-200 tun
    This causes the TUN/TAP driver to be loaded automatically when the /dev/net/tun device is opened by Hercules.

Installing the TUN/TAP Driver (Linux 2.6)

For distributions based on the Linux 2.6 kernel you will probably find that the TUN/TAP driver is already installed and the /dev/net/tun device is already defined. If not, then follow the procedure for Linux 2.4 as descibed above.

You will certainly need to alter the permissions on the /dev/net/tun device to allow Hercules to open it.

In Linux 2.6 the file /etc/modules.conf no longer exists, instead there is a file called /etc/modprobe.conf. TUN/TAP will usually work, however, without any change to the modprobe configuration.

Configuring the TUN interface

The tun0 network interface in the driving system must be configured as a point-to-point link. The design of the TUN/TAP driver does not allow the interface to be statically configured like a regular network interface — the tun0 interface does not exist until Hercules opens the TUN device. For this reason, Hercules provides a special program called hercifc to configure the tun0 network interface. This program is launched automatically by Hercules 3088 CTC device initialization.

To allow the hercifc program to issue the necessary configuration commands, you must ensure that hercifc is installed with setuid root file permissions. When Hercules is built with the configuration option --enable-setuid-hercifc, make install will install hercifc in /usr/local/bin with setuid root permissions. Note: Unrestricted access to the hercifc program could present a potential security exposure, so you will want to ensure that hercifc can be executed only by the group which is authorized to run Hercules. The following commands alter the file permissions to ensure that only users in a trusted group can execute hercifc:
(enter the root password when prompted)
chgrp xxxxx /usr/local/bin/hercifc
(where xxxxx is the group under which you run Hercules)
chmod 4750 /usr/local/bin/hercifc

Enabling IP forwarding

You must ensure that your kernel is enabled for IP forwarding. Popular Linux distributions usually have a configuration option to enable IP forwarding or routing:

Defining a route to Hercules TCP/IP

Client systems which connect to TCP/IP applications running in the Hercules machine need to have a routing entry which defines the driving system as the gateway into the Hercules system. An example route definition for a Unix client system is shown below:

route add gw

For a Windows client, go to Settings -> Control Panel -> Network -> Configuration -> TCP/IP -> Properties -> Gateway and add the driving system's IP address to the list of gateways. Alternatively, enter a route command such as:

route add mask metric 1

If you want to avoid having to update client systems, another way is to add an appropriate routing entry to your default gateway router.

Defining the link in Hercules

You must define a CTC device pair in the Hercules configuration file. The second device must bear the same definition as the 1st instance and be at device number + 1. The 1st device number must be even. Devices should preferably be grouped (furthermore, it makes the configuration file easier to read).

0E20.2 CTCI
0E20,0E21 CTCI
0E20-0E21 CTCI

Check Device Definition Statement syntax for an explanation of device grouping.

Two IP addresses must be assigned, one for the driving system's end of the link, and one for the Hercules end of the link. For this example I have chosen for the Hercules IP address, and for the driving system's IP address. Since this is a point-to-point link, any addresses may be chosen, provided that the network part of the address (192.168.200 in this example) does not conflict with any existing network addresses used in your IP network.

Configuring the Hercules TCP/IP stack


This is an example of the configuration statements which you need to include in the IPINIT00.L member of PRD1.BASE:

SET MASK     =

The CTC devices should be defined to VSE using the following statements in the $IPLxxx.PROC procedure in IJSYSRS.SYSLIB:


TCP/IP for OS/390 or VM/ESA

This is an example of the configuration statements which you need to include in the TCPIP.PROFILE.TCPIP dataset (OS/390), or in the PROFILE TCPIP file on TCPMAINT 198 (VM):

; Network      First Hop     Link Name Size   Subnet Mask  Subnet Value  =             CTCLINK1  1500   HOST

For OS/390, the CTC devices need to be defined as device type 3088 in the IODF. Use the D U,CTC command to find out which 3088 addresses are defined in your IODF.

For VM, the CTC devices must be attached to the TCPIP virtual machine.

Because TCP/IP uses long running channel programs, the missing interrupt handler should be disabled for the CTC devices. For OS/390, add this statement in PARMLIB member IECIOS00:

MIH TIME=00:00,DEV=(E20-E21)

For VM, add this command to the PROFILE EXEC file of OPERATOR 191:


Linux for S/390

This is an example of the network definitions which you need in a Linux/390 system running under Hercules:

ifconfig ctc0 pointopoint mtu 1500
route add defaultroute gw

Linux/390 will autodetect the CTC devices E20 and E21 at startup and will assign the interface name ctc0.

What to do if TUN/TAP doesn't work

Check the following (thanks to Richard Higson for this checklist):

  1. Enter the command ls -l /dev/tun0 /dev/net/tun.
    For Linux 2.4, the response should be:
    ls: /dev/tun0: No such file or directory
    crw-rw---- 1 root xxxxx 10, 200 Sep 13 07:06 /dev/net/tun

    For Linux 2.2, the response should be:
    crw-rw---- 1 root xxxxx 90, 0 Feb 3 2001 /dev/tun0
    ls: /dev/net/tun: No such file or directory

    (xxxxx should be the group under which you run Hercules).
  2. ls -l /usr/local/bin/hercifc should show
    -rwsr-x--- 1 root xxxxx 17333 Dec 31 20:55 /usr/local/bin/hercifc

    (xxxxx should be the group under which you run Hercules).
  3. When hercules comes up, and before IPLing your favorite OS, verify that you have your underlying network stuff up and ready to roar:
    [root]# ifconfig
    eth0      Link encap:Ethernet  HWaddr 00:12:34:56:78:9A
              inet addr:  Bcast:  Mask:
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
    tun0      Link encap:Point-to-Point Protocol
              inet addr:  P-t-P:  Mask:
    [root]# netstat -in
    Kernel Interface table
    eth0   1500   0     201      0      0      0     196      0      0      0 BMRU
    tun0   1500   0       0      0      0      0       0      0      0      0 MOPRU
    [root]# netstat -rn
    Kernel IP routing table
    Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface       U        40 0          0 eth0   U        40 0          0 tun0       U        40 0          0 lo         UG       40 0          0 eth0
  4. `cat /proc/sys/net/ipv4/ip_forward` should show "1". If it doesn't, your L386 won't forward (==route) packets at all.
  5. Is the TUN/TAP driver loaded?
    1. TUN/TAP compiled into the kernel (`make menuconfig`) look for "CONFIG_TUN=m" in /usr/src/linux
    2. `lsmod` after starting hercules should show tun 3456 2 (autoclean)
  6. Look for
    Dec 14 16:47:19 wie kernel: Universal TUN/TAP device driver 1.3 (C)1999-2000
    Maxim Krasnyansky

    in syslog after starting hercules


Last updated $Date: 2007-01-31 11:06:10 -0600 (Wed, 31 Jan 2007) $ $Revision: 4282 $